Notice: Undefined offset: 8192 in /home/marmagul/public_html/gallery/include/ on line 112 Beer and Brewing Gallery - Last additions



| Home | Beer Forum | Brew Forum | Tutorials | Calcs | Recipes | Humour | Gallery | Beer Glossary | Directories & Links | Contact Us |

Anyone can upload beer and brewing pictures to the gallery. All you need to do is create a Gallery  account, Login and click 'Upload file' Beer and Brewing Gallery

NOTE:WE NO LONGER CAN ACCPT NEW USERS DUE TO SPAMMERS To upload your Beer and Brewing Pictures click on 'Upload file' below (must be logged in). PLEASE NOTE: FILES UPLOADED MUST BE SMALLER THAN 2000KB. For more info click on 'More FAQ & Di

Home :: FAQ :: Login
More FAQ & Discussion :: Album list :: Last uploads :: Last comments :: Most viewed :: Top rated :: My Favorites :: Search

Last additions - Taz
HLT upgrade7736 viewsAutomated HLT filling. This was done using a simple two stage controller. The sensors are home made as I couldn't find anything off the shelf. These were made up of 1/2 inch BPT nipples welded top and bottom with plastic end caps used in rural irrigation to electrically isolate the probes from the keg which acts as ground. These caps were boiled in an electric jug for 15 minutes to test for heat and they stood up well. The probes used were stainless steel screws and nuts. Corrosion and electrolysis can be a real problem with this sort of gear.
1 commentsTazOct 19, 2011
HLT upgrade4546 viewsTop water level sensor. Solenoid valve just seen on the riight.TazOct 19, 2011
HLT upgrade4610 viewsWater level sensorTazOct 19, 2011
Mindy7915 viewsFearless rat catcher protector of the grain supply and brew assistantTazAug 26, 2010
My brew assistant6856 viewsThe brew assistant doing what she does best between eating and hunting.TazAug 26, 2010
March Pump6926 viewsAn ungarded March Pump that needed a cover of some sort.TazAug 08, 2010
March Pump7225 viewsWasn't long before I realized the March Pump wasn't going to last long without some sort of protection against water and hot wort getting ito the cooling slots so I had this cover made upTazAug 08, 2010
6915 viewsTurning a 60 litre Sankey keg into a 85 litre one. The need to brew triple batches to fill 3 corny kegs I found the 60 litre keg was a tad to small which didn't allow for evaporation and head room for hot break, this is how I approached the problem. I cut the middle out of a damaged keg scavenged from an apple orchard.TazAug 08, 2010
5644 viewsI cut my existing Sankey boiler in half (gulp) then welded the bottom half to the salvaged keg, then finished the weld off inside grinding and polishing. I needed a torch in the bottom for this.TazAug 08, 2010
5696 viewsAdd the top, weld into place grind and polish inside. Stainless Steel will rust if the surface is not polished smooth so a bit of work is needed to bring the welded areas up to a good finish. The end result was a good sized boiler at a cheap price.TazAug 08, 2010
Brewrig3536 viewsAnother brew day finished and all cleaned up.TazJul 23, 2010
Cranking up the boiler2991 viewsBoiling a 60L batch in a modified kegTazJul 23, 2010
My Brewrig3345 viewsBrew day filling the fermenter through the CFCTazJul 23, 2010
13 files on 1 page(s)

| Home | Beer Forum | Brew Forum | Tutorials | Calcs | Recipes | Humour | Gallery | Beer Glossary | Directories & Links | Contact Us |

All pictures and pages on this gallery are licensed under a Creative Commons licence, Attribution Non-commercial Share Alike 3.0. In addition to this license, by contributing to this gallery you are giving the administration of non-exclusive permission to use your contribution under the same conditions as contributing to our beer glossary (click here to view). To view the Creative Commons  license click on the icon to the left.

You are unique visitor number to

Copyright 2008